How to Set up a Tub: Install an Acrylic Bathtub as Well as Tub Surround
How to Set up a Tub: Install an Acrylic Bathtub as Well as Tub Surround
Blog Article
This great article following next pertaining to How to Install a Bathtub Yourself is relatively entertaining. Check it out yourself and decide what you think about it.
Setting up a tub isn't specifically rocket science, however it does call for solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bathtub with a new one is additionally a moderately challenging task. If the old tub is easily obtainable, the project can move easily; if you have to open a wall surface to get rid of the old tub as well as place the brand-new bath tub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and set in the new one. See to it you have qualified on your own for the work and are comfortable attempting it. As opposed to working with a contractor to take over a halfway-completed task, it is better to think about utilizing one prior to you start. Opportunities are you may need a professional plumber to make tube connections.
This post will certainly aid you mount a new bathtub in your restroom if you have currently gotten a brand-new bathtub and also do not require to transform the arrangement of your previous supply of water pipes.
Your tools as well as material list must consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is separate the water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome due to the restricted access that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a towel prepared for the staying water that will come from the pipes. As soon as the supply pipelines have actually been eliminated, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning throughout this procedure. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Before moving on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin making sure that the washers remain in place between the faucet as well as the sink. Safeguard the tap in place with the manufacturer supplied backnut. When the tap is safely in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical tap ports. The previous type ought to be attached to the tap finishes first, tightening only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Tub
Making use of the two wood boards under its feet, place the tub in the called for setting. The wood boards are useful in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four little factors.
The next objective is to ensure that the bathtub is leveled all round. This can be attained by examining the spirit level and also adjusting the feet on the bathtub till the spirit level checks out degree.
To mount taps, fit the bottom of the outermost flexible tap adapter to the appropriate supply pipe by making a compression sign up with; after that do the same for the various other tap.
Turn on the water system and check all joints as well as brand-new pipework for leaks and tighten them if needed. Load the bath tub and likewise inspect the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, fix the bath paneling as explained in the supplier's instruction manual. Tiling and sealing around the tub needs to wait till the bath tub has been utilized a minimum of when as this will certainly resolve it right into its final position.
Preparing for the Setup
First of all, the sustaining structure provided with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to stop pressure on the tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you make use of every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must now be ready to be suited its final position.
Tiling Around the Bath tub
In the location where the bath fulfills the floor tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to fracture a stiff seal, triggering the water to penetrate the wall surface in between the bath and also the tiling, causing problems with dampness and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill up the bath tub with water before securing, to allow for the activity experienced when the tub remains in use. The sealer can crack relatively very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily available on the marketplace. It is recommended to fit the floor tiles using water-resistant or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a passionate reader about How to Install a Bathtub Yourself, I was thinking sharing that piece of content was important. Feel free to set aside a second to share this blog posting if you enjoyed it. Many thanks for going through it.
View Website
Report this page